Better make sure the address value included in the event message gets
cleared in case the GO Device Address is not known for some reason.
Previously, this could potentially have been some random data from
stack should we ever hit the case where wpa_s->current_ssid is not
set (which should not really happen in normal use cases).
This adds the ability to add WPS vendor extension attributes in P2P
frames, like GO Negotiation and Probe Response frames.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a notification function for the result of an invitation.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a notification for received GO negotiation requests.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous code was assuming that the P2P module is always initialized.
However, that is not the case anymore with drivers that do not support
P2P. Add verification of whether P2P is enabled before trying to execute
P2P commands.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
When the network was provisioned, we need to get the keys to be able to
reconnect without new provisioning. To be able to publish those keys but
not normally configured ones, add a new attribute to struct wpa_ssid
indicating whether or not keys may be exported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two issues with p2p_long_listen:
1) max_remain_on_channel is assumed to be 5 seconds,
2) if max_remain_on_channel is not a full multiple of
seconds, accounting breaks.
Fix these by converting p2p_long_listen to ms and
tracking it according to max_remain_on_channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a pending GO Negotiation when p2p_cancel is used,
unauthorize the peer to avoid immediate reconnection from being
accepted without a new p2p_connect command.
We should cancel group formation completely on PBC overlap instead
of just partially notifying that operations were stopped. There is
no point in waiting for the group formation timeout in this case.
WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P flag can now be used to
indicate that the initial interface (e.g., wlan0) is used for
P2P management operations and potentially non-P2P connections.
This is otherwise identical to
WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE, but the possibility of
non-P2P connections makes some operations differ.
This may make it less likely for udev to rename the interface that
would previously have been called wlan0-p2p-# (now: p2p-wlan0-#).
In addition, add some workaround code to handle the case where the
main interface name is close to the IFNAMSIZ length limit to
avoid going over that for the P2P group interface.
We can automatically accept invitations that are for a persistent
group that is already running. There is no need to confirm this
separately or preparare a new group interface.
When an Invitation to reinvoke a persistent group is accepted,
we need to make sure that any pending p2p_find or p2p_listen
operation gets stopped to avoid consuming all radio resources
doing device discovery while the group is being set up.
This pointer is now used in number of places to check whether an
interface is in P2P Group Formation, so we better make sure it gets
cleared when group formation has been completed. This was done in
only some of the cases.
The pending_invite_ssid_id of -1 (running group, not persistent) was
being stored incorrectly in the group interface, not device interface
(i.e., parent of the group interface) and consequently, the incorrect
information was used when processing the Invitation Response.
If there was a persistent group credentials stored with network id
0, those were used instead to try to set up a persistent group
instead of using the already running group.
Since the P2P peer entry may not have been available at the time the
join request was issued, we need to allow the P2P Interface Address
to be updated during join-scans when the P2P peer entry for the GO
may be added.
If the GO is not found, we cannot send Provisioning Discovery Request
frame and cannot really connect anyway. Since the Provisioning
Discovery is a mandatory part, it is better to continue join-scan
until the GO is found instead of moving to the next step where
normal connection scan is used (PD would not be used from there).
Use a limit of 10 scan attempts for p2p_connect join to avoid getting
in infinite loop trying to join. If the GO is not found with those
scans, indicate failure (P2P-GROUP-FORMATION-FAILURE) and stop the
join attempt.
When running "p2p_connect addr pbc join" command, send the
WPS-OVERLAP-DETECTED even also to the parent interface (i.e.,
the one on which the p2p_connect was issued) and not only the
group interface in case separate P2P group interfaces are used.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
The driver may end up leaving the current channel when we request
a new remain-on-channel and as such, it is better not assume we can
start new operations like sending an Action frame on the previous
off-channel.
If we have already asked the driver to start a new remain-on-channel,
we need to cancel it even if the actual remain-on-channel has not yet
started at the point when a new operation or timeout etc. triggers
Listen state to be stopped.
Even if p2p_scan_res_handler() returns 1 to indicate that scan result
iteration should be stopped, the p2p_scan_res_handled() needs to be
called to clear p2p_scan_running and to get a callback that will start
any operations that were delayed because of the running scan.
