This is the first step in allowing SA Query mechanism in hostapd to be
used with drivers that implement authentication and association MLME/SME
(i.e., do not use ieee802_11.c).
New configuration parameters home_imsi and home_milenage can be used
to configure SIM/USIM simulator parameters for network selection based
on SIM/USIM credentials.
home_imsi=(MCC | MNC | '-' | rest of IMSI)
home_milenage=(Ki):(OPc):(SQN)
For example:
home_imsi=310026-000000000
home_milenage=90dca4eda45b53cf0f12d7c9c3bc6a89:cb9cccc4b9258e6dca4760379fb82581:000000000123
Add support for network selection for username/password credentials with
EAP-TTLS and EAP-PEAP. The new global configuration parameters
home_username, home_password, and home_ca_cert can be used to specify
credentials for network selection.
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
Add mechanism for using GAS/ANQP to query Interworking related
information from APs. The received information is stored in the BSS
table and can be viewed with ctrl_iface BSS command.
New ctrl_iface command ANQP_GET can be used to fetch ANQP elements from
a specific AP. Additional commands FETCH_ANQP and STOP_FETCH_ANQP can be
used to initiate and stop an iteration through all APs in the BSS table
that indicate support Interworking to fetch ANQP elements from them.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
EVENT_WPS_BUTTON_PUSHED wpa_supplicant_event can now be used in
station mode driver_*.c to indicate that a push button has been
pushed. This will activate WPS PBC mode.
When initializing, the scheduled scan code was being called before
everything is ready. With normal scans, the first scan round is
delayed, so the initialization is finished by the time it really
starts.
Add a function that can be used to request a delayed scheduled scan.
The scan will only start after the specified time has elapsed. Call
this function instead of starting the scheduled scan directly during
driver initialization.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch uses sched_scan, if available, when the driver is
initialized. It also adds a couple of cancel operations where
appropriate.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move some code to separate functions to reorganize the P2P and WPS
handling during scans. This makes the code a bit cleaner and is
needed for the scheduled scan implementation to avoid duplicated code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clear the P2P GO callback parameters when removing the group to avoid
using these for non-P2P AP mode.
This is a fix for the bug I found in the following scenario:
A) p2p_group_add
A) p2p_group_remove wlan0
A) add_n
A) set_n 0 ssid "testap"
A) set_n 0 key_mgmt NONE
A) set_n 0 mode 2
A) set_n 0 frequency 2412
A) enable_n 0
B) try connect to testap
Authentication request will be always rejected because of
HOSTAPD_ACL_REJECT and not cleaned callbacks when group removed.
This allows the AP to be selected based on the BSSID when WPA-PSK
is used with a passphrase. The PSK will be derived from the passphrase
after the SSID has been learned from scan results.
This implements GAS request mechanism that is aimed at being used to
replace use case specific GAS/ANQP implementations in the future.
Compared to the earlier implementation in P2P SD, this implementation
includes support for multiple concurrent requests and more thorough
validation of frames against the pending query data.
GAS header processing, including comeback and reassembly, are handled
within gas_query.c and the users of this module will only need to
provide the Query Request and process the (possibly reassembled)
Query Response.
GAS/ANQP is a generic protocol and in no way specific to P2P, so move
routines used to build GAS/ANQP frames to a separate file that can be
shared for other uses than just P2P service discovery.
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.
Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
If the initial attempt to start a scan for p2p_find fails, an error
is reported. However, the P2P scan handler and search state was
left behind. That can result in unexpected behavior when the next
non-P2P scan results are indicated. Avoid this by clearing the
P2P search state on failure.
There is no need to request periodic bgscans when the driver claims
to have capability for roaming within ESS. Ignoring the bgscan
configuration allows the same configuration file to be used both
with drivers the handle roaming and with drivers that don't.
If the driver indicates that it supports BSS selection (including
roaming within an ESS) with WPA_DRIVER_FLAGS_BSS_SELECTION, modify
ap_scan=1 mode to behave like ap_scan=2 mode for BSS selection.
The initial scan is still done to avoid the need for strict
configuration of or security parameters (e.g., to figure out whether
TKIP or CCMP is being used as the group cipher). However, when
requesting the driver to connect, the bssid and freq parameters are
not provided to leave the driver in control of selecting which BSS
to use and to allow the driver to decide when to roam.
These protocols seem to be abandoned: latest IETF drafts have expired
years ago and it does not seem likely that EAP-TTLSv1 would be
deployed. The implementation in hostapd/wpa_supplicant was not complete
and not fully tested. In addition, the TLS/IA functionality was only
available when GnuTLS was used. Since GnuTLS removed this functionality
in 3.0.0, there is no available TLS/IA implementation in the latest
version of any supported TLS library.
Remove the EAP-TTLSv1 and TLS/IA implementation to clean up unwanted
complexity from hostapd and wpa_supplicant. In addition, this removes
any potential use of the GnuTLS extra library.
wpa_supplicant returns the PIN in reply to the connect method. Treating
this value as an integer runs the risk of not returning the correct
value if the first digit(s) happens to be a zero(es). To return the
correct PIN it needs to be returned as a string.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
The default discovery type is to search for devices only on social
channels. Expand this to also support an initial full scan followed by the
scan of social channels as well as the progressive scan that scans through
all the channels in the Search state rounds. This does not change the
default of scanning only social channels although there is currently a
discrepancy wrt the default used by wpa_cli, which is the full scan first.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
When parsing a dict entry which is an array of an array of bytes the entry
representing the dict entry has DBUS_TYPE_ARRAY as its type and
WPAS_DBUS_TYPE_ARRAY as its array_type. The function freeing this parsed
data incorrectly tested the entry type for WPAS_DBUS_TYPE_ARRAY while doing
no testing of this value for array_type. This results in a memory leak
whenever a D-Bus message with this type of data is parsed.
Messages affected are:
fi.w1.wpa_supplicant1.Interface.P2PDevice
using RequestedDeviceTypes with Find method
using SecondaryDeviceTypes or VendorExtension with P2PDeviceProperties
fi.w1.wpa_supplicant1.Group
using WPSVendorExtensions with Properties property
All of the above messages are parsed with the same function,
wpa_dbus_dict_get_entry, so the assignment of the entry's type and
array_type is consistent. The parsed data is also consistently freed with
the same function, wpa_dbus_dict_entry_clear, so we can use the same checks
to free the data correctly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
The action done handling needs to abort an off-channel period since one
might have been used for example for GO negotiation and after action
done the code assumes it can start a new off-channel period.
This fixes a bug I introduced when adding support for
in-kernel off-channel transmissions.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
eapol_test command line argument -o<file> can now be used to request
the received server certificate chain to be written to the specified
file. The certificates will be written in PEM format. [Bug 391]
The proactive_key_caching parameter was missed in mapping the
config_ssid data into the WPA state machine configuration. This
prevented addition of PMKSA cache entries based on PMKSA caching
candidate events.
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
If a network configuration block is removed or modified, flush
all PMKSA cache entries that were created using that network
configuration. Similarly, invalidate EAP state (fast re-auth).
The special case for OKC on wpa_supplicant reconfiguration
(network_ctx pointer change) is now addressed as part of the
PMKSA cache flushing, so it does not need a separate mechanism
for clearing the network_ctx values in the PMKSA cache.