The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
The duplicated WPS event in the parent interface should only be used
during P2P group formation, i.e., when the WPS operation was actually
started using the parent interface. When authorizing a client to
connect to an already running group, the WPS command is issued on
the group interface and there is no need to duplicate the event to
the parent interface.
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change then.
In other words, the protocol is allowed to continue past M2, but
is stopped at M7 when AP is in this mode. WPS IE does not
advertise AP Setup Locked in this case to avoid interoperability
issues.
In wpa_supplicant, use ap_setup_locked=2 by default. Since the AP PIN
is disabled by default, this does not enable any new functionality
automatically. To allow the read-only ER to go through the protocol,
wps_ap_pin command needs to be used to enable the AP PIN.
This driver capability limit was supposed to indicate limit on
how many stations can associate with us in the AP mode, not how
many P2P peers are stored in the peer table.
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
This command is supposed to return the PIN value that was generated
or passed in as an argument. In the AP case, the entered PIN was not
being returned.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This allows the driver interface to be deinitialized before
struct hostapd_data instance gets freed. This needs to be done so
that the driver wrapper does not maintain a context pointer to
freed memory.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
Initialize struct hostapd_data driver context with the same driver
information that was initialized earlier during wpa_supplicant start.
This allows the AP mode operations to be completed directly with the
same calls in AP code without having to maintain a separate translation
layer between the AP and station mode driver context.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
This mode allows associated stations to use 4-address frames to allow
layer 2 bridging to be used. At least for the time being, this is only
supported with driver=nl80211.
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
