Commands like BSS and GET_NETWORK are used in some cases very frequently
and those can increase the amount of debug information from
wpa_supplicant without significant benefit. These were logged at the
DEBUG level (-d). Move logging of such read-only commands (i.e., no new
wpa_supplicant operation is started based on it) to EXCESSIVE level
(-ddd) which was already used for the PING command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the BSS command returned an error if the WSC IE(s) in scan
results could not be parsed. This may be not ideal for all cases, to
instead of rejecting the command completely, return all other
information apart from the WPS information in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.
Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Change P2PS P2P-PROV-SHOW-PIN/P2P-PROV-ENTER-PIN event notifications
on PD Request/Response handling to meet required P2PS behavior.
The new implemented scheme:
1. For a legacy P2P provision discovery the event behavior remains
without changes
2. P2PS PD, advertiser method: DISPLAY, autoaccept: TRUE:
Advertiser: SHOW-PIN on PD request replied with a status SUCCESS
Seeker: ENTER-PIN on PD response received with a status SUCCESS
3. P2PS PD, advertiser method: DISPLAY, autoaccept: FALSE:
Advertiser: SHOW-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: ENTER-PIN on Follow-on PD request with a status
SUCCESS_DEFERRED
4. P2PS PD, advertiser method: KEYPAD, autoaccept: TRUE/FALSE:
Advertiser: ENTER-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: SHOW-PIN on PD response received with a status
INFO_CURRENTLY_UNAVAILABLE
This change in behavior breaks the existing test cases
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept. Those will be fixed in a
followup commit.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
P2P_FLUSH command did not cleanly clear the p2p_go_avoid_freq data
structure, and left it in an inconsistent state, where the range field
was NULL but the num field was not 0. This would have resulted in an
invalid memory access in freq_range_list_includes().
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.
To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes it possible to use these helper functions from hostapd as
well as the current use in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a parameter allowing to specify a value of Coordination
Protocol Transport to P2PS_PROVISION and P2PS_PROVISION_RESP commands.
Extend the p2ps_provision structure to contain cpt_priority and
cpt_mask properties and initialize them on a P2PS PD request command.
The format of the parameter:
cpt=<cpt>[:cpt]
where <cpt> is CPT name e.g. UDP or MAC. The CPT names are listed
according to their preferences to be used for a specific P2PS session.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Do not allow wpa_s->fst to be replaced when processing FST-ATTACH
command for an interface that has already been attached.
Signed-off-by: Jouni Malinen <j@w1.fi>
This header file is needed to get struct fst_iface_cfg and struct
fst_wpa_obj defined. While it does currently get pulled in through
ap/hostapd.h and ap/ap_config.h, a more explicit inclusion may be a
cleaner option for future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This command allows network variables to be copied from one network to
another when the networks belong to different radios. This is similar to
the per-interface DUP_NETWORK command. On the global control interface,
the command syntax is as follows:
DUP_NETWORK <src ifname> <dst ifname> <src network id> <dst network id> <variable name>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The IPv4 header after the Ethernet header is not 32-bit aligned and the
previous version ended up accessing 32-bit members at misaligned
addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.
As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
In p2p_find command line processing a loop searching for multiple
'seek=' parameters modifies cmd buffer adding '\0' terminators.
The 'freq=' parameter is handled after that and can be
lost if a 'freq=' follows 'seek=' in a command line.
Fix it by moving a handling of 'freq=' parameter to be processed
before 'seek=' handling loop.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
p2p_ctrl_group_add() takes care of various configuration options (such
as ht/vht) before calling wpas_p2p_group_add(), so use it (just like
when P2P_GROUP_ADD is called with additional params).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Parse each parameter individually and combine all the function calls.
This will allow further patch to call it with no parameters (currently
this might result in failure).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Only the first seek=<service name> parameter was accepted from the
P2P_FIND command. Fix this to go through all seek parameters to
construct the list of service hash values to seek.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where a disconnection event may get ignored if an
earlier operation to remove or disable a network resulted in an attempt
to disconnect event though no connection was in place.
wpa_s->current_ssid != NULL alone is not sufficient to determine that
there will be a driver event notifying completion of such disconnection
request. Set own_disconnect_req to 1 only if wpa_s->wpa_state is also
indicating that there is a connection or an attempt to complete one.
This showed up in a failure, e.g., when running the hwsim test case
scan_int followed by ap_vlan_wpa2_psk_radius_required where the latter
ended up not processing a connection failure event and getting stuck not
trying to run a new scan and connection attempt.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the TDLS_LINK_STATUS command to the control interface. This command
shows what is the status of our current TDLS connection with the given
peer. Also, add the TDLS_LINK_STATUS command to wpa_cli.
Signed-off-by: Oren Givon <oren.givon@intel.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression caused by commit
efa232f915 ('Add support for virtual
interface creation/deletion') for the case where an empty extra argument
is included.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Extend interface_add and interface_remove commands via an optional
argument to allow wpa_supplicant to create/delete a new virtual
interface.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Extend p2p_service_del asp command to support 'all' parameter to delete
all ASP service advertisements.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reject external scan request while either ANQP fetch or Interworking
select is in progress. Not doing so could lead to a situation in which
Interworking automatic network selection does not get triggered because
of a new scan result event forcing the ANQP fetch cycle to be disrupted
and restarted all over again. Interworking automatic network selection
is only triggered when AQNP fetch cycle, that is, ANQP exchange with
every Interworking capable BSS in the current BSS list, is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the P2P_CONNECT control interface command to be
issued on an incorrect interface. While the upper layer component should
really use global control interface for this, make this work by
redirecting the command to the correct context if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, add support for returning the capability list through
the BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
In addition, add support for returning the capability list through the
BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
This can be used to provide more control to upper layers on network
blocks generated as part of Interworking network selection.
INTERWORKING_ADD_NETWORK behaves otherwise identically to
INTERWORKING_CONNECT, but it does not request a new connection after
having added the network block and it returns the network id of the
added network.
INTERWORKING_ADD_NETWORK followed by REASSOCIATE would behave more or
less identically to INTERWORKING_CONNECT, but this allows the created
network profile to be modified, if desired, and/or stored externally.
SELECT_NETWORK can also be used with the network id returned from
INTERWORKING_ADD_NETWORK to enforce that specific network profile to be
used for the next connection (though, it should be noted that this
behavior may not meet all Hotspot 2.0 requirements if there were other
enabled networks that could have higher priority).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b31be3a0fd ('P2P: Add automatic GO
Negotiation vs. join-a-group selection') added this P2P_CONNECT 'auto'
parameter, but did not update any documentation on it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 07cb45ccb2 ('mesh: Add no_auto_peer
config option') added a new struct wpa_ssid argument and added an
unnecessary parsing and setting of the value in
wpa_supplicant_ctrl_iface_update_network(). This is not needed since
wpa_config_set() takes care of parsing the parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a network profile to change its type from P2P
persistent group to a normal network and back. The D-Bus interface uses
different types of objects for those, so the object needs to
re-registered in case of type change. This fixes issues in leaving
behind an incorrect type of object and leaking memory when freeing such
a network block that has had its disabled parameter changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow P2PS related new control interface commands to
be redirected for proper context processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands
P2P_ASP_PROVISION and P2P_ASP_PROVISION_RESP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the P2P_SERV_DISC_REQ control interface command with a new
"asp" service type. This takes service id, service string, and optional
service info as arguments.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add a new P2P_SERVICE_REP command that can be used to
replace existing ASP advertisements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides additional WPS definitions and rules for negotiating use
of P2PS default PIN configuration method.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
P2PS seek strings can now be specified in the P2P_FIND control interface
command with one or more optional "seek=<str>" parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends GET_CAPABILITY command to allow the supported group
management frame cipher suites to be listed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A control interface call to flush the current state used the
current wpa_s to clear the P2P state even though it might not
be the interface controlling the P2P state.
Fix it by using the correct interface to flush the P2P state.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The length should be 14 and not 10.
The current situation causes failure during parsing of the command.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the wpa_bss_flush() call to the end of the function to allow any
pending user of a BSS entry to be cleared before removing the unused
entries. There were number of cases where BSS entries could have been
left in the list and this resulted in some hwsim test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
For Interworking connection to work, the SSID of the selected BSS needs
to be known to be able to associate with the AP. It was possible for the
scan results to include two BSS entries matching the BSSID when an
earlier scan with that AP has shown a hidden SSID configuration (e.g.,
when running hwsim test cases, but at least in theory, this could happen
with real use cases as well). When that happened, the incorrect BSS
entry may not have included RSN configuration and as such, it would get
rejected for Interworking connection.
Fix this by confirming that the selected BSS entry has a real SSID. If
not, try to find another BSS entry matching the same BSSID and use that,
if found with an SSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new wpa_supplicant and hostapd control interface command can be
used to determine which TLS library is used in the build and what is the
version of that library.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command TEST_ALLOC_FAIL and GET_ALLOC_FAIL can
now be used to trigger memory allocation failures for testing purposes.
TEST_ALLOC_FAIL sets a failure conditions with
<count>:func[;func][;func]... string and GET_ALLOC_FAIL returns the
current state using the same format. Whenever an allocation is made with
a matching backtrace of calling functions, the count is decremented by
one and once zero is reached, the allocation is forced to fail.
Function names can be prefixed with either '=' or '?' to get different
matching behavior. '=' requires this specific function to be the next
one in the backtrace (i.e., do not skip any other functions in the list
which is the default behavior). '?' allows the function to be optionally
present in the backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
It was possible for old scan state to remain from a previous test case
when an operation like WNM neighbor scan or another-BSS-in-ESS was
started, but stopped at the end of a test case. This could result in
failures, e.g., when running wnm_bss_tm_req followed by scan_setband.
Signed-off-by: Jouni Malinen <j@w1.fi>
This helps hwsim test cases by avoiding undesired state from previously
executed test cases affecting following tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit faf9a8585d added mechanism for
selecting 2.4 or 5 GHz band for scan operation. However, no mechanism
for setting the setband value was added at that time. This commit adds a
new SET ctrl_iface parameter to allow the setband functionality to be
used. "SET setband <AUTO/5G/2G>" can be used to select all bands, 5 GHz
band only, or 2.4 GHz band only.
Signed-off-by: Jouni Malinen <j@w1.fi>
FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.
If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.
Signed-off-by: Jouni Malinen <j@w1.fi>
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.
Signed-off-by: Vinit Deshpande <vinitd@google.com>
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
This wmm_ac_status command will show the current status for WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
These key management options were missing from the previous set of
parsed information in scan results.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 86bd36f0d5 ("Add generic
mechanism for adding vendor elements into frames") has a minor bug
where it miscalculates the length of memory to move using
os_memmove. If multiple vendor elements are specified then this can
lead to out of bounds memory accesses.
This patch fixes this by calculating the correct length of remaining
data to shift down in the information element.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
It also allows to use the STATUS command with default behavior,
say for debug, i.e., don't generate a "fake" CONNECTION and
SUPPLICANT_STATE_CHANGE events with the new STATUS-NO_EVENTS case.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.
The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"TDLS_TEARDOWN *" can now be used to tear down the direct links to all
TDLS peers. This is useful for debugging purposes.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Due to an incorrect operation (MOD vs. AND), the code that was supposed
to return an error if the hex string has odd length was not really
reporting any failures. Instead of reporting an error, the invalid
control interface command would have been truncated. This is not an
issue in practice, but better fix the implementation anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
The dynamically allocated struct wpa_external_work contains the name of
the radio work in the type field and this is used in a debug print
within radio_work_done(). Re-order radio_work_done() and os_free() calls
on couple of paths where the memory was freed before that final user of
the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
This new command can be used to simulate driver events without having to
go through the driver wrapper or kernel code for this. This enables more
testing coverage with hwsim.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This command allows to copy network variable from one network to
another, e.g., to clone the psk field without having to extract it from
wpa_supplicant.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
No need to use ENOBUFS within core wpa_supplicant, so just replace it
with -1 to work arounds MinGW build issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version prevented all use of wpas_global_ctrl_iface_set().
That's not desirable since there may be more global parameters added in
the future. Instead, try to use the global version first and redirect to
P2P interface only if the global version returns an error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P redirection for SAVE_CONFIG issued on the global control
interface was preventing wpas_global_ctrl_iface_save_config() from being
reached. The global version of SAVE_CONFIG was supposed to try to save
configuration files for all interface rather than just the P2P
management interface, so fix this by removing the unneeded and undesired
redirection.
Modify the global SAVE_CONFIG handler to return FAIL if no configuration
files were saved. This makes the behavior match with the per-interface
SAVE_CONFIG.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Adding a new entry was returning FAIL on success due to incorrect
assumption of wpa_blacklist_add() returning 0 on success (it returns the
positive blacklist count).
Signed-off-by: Jouni Malinen <j@w1.fi>
These commands can be executed on the P2P interface thus should be
redirected to it when issued to the global control interface.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Commit 41d5ce9e0b added scan optimizations
for P2P invitation cases. However, it left a path where the invitation
state was not cleared and as such, introduced potential issues for
following scans that ended up getting incorrectly optimized for a single
channel regardless of parameters. Fix this by clearing p2p_in_invitation
more carefully, especially on p2p_cancel command.
p2p_cancel is now also run from the FLUSH command to avoid issues with
hwsim test cases (e.g., persistent_group_per_sta_psk followed by
ap_open_tdls resulted in an error due to p2p_in_invitation remaining set
after FLUSH).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The newer NFC_REPORT_HANDOVER command is more general version that
handles the cases where NFC_RX_HANDOVER_SEL could potentially have been
used. In addition, with the new WPS NFC design, it is important to
receive the handover request message that was used in the handover in
addition to the select message, so the NFC_RX_HANDOVER_SEL command on
its own would not be sufficient for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a subset of channels to be specified for the scan used to
find the network when the SELECT_NETWORK ctrl_iface command is issued.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:
CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows a single ANQP query to be used to fetch both IEEE 802.11
defined ANQP elements and Hotspot 2.0 vendor specific elements.
ANQP_GET <addr> <info id>[,<info id>]...
[,hs20:<subtype>][...,hs20:<subtype>]
For example:
ANQP_GET 00:11:22:33:44:55:66 258,268,hs20:3,hs20:4
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"SET blob <name> <hexdump>" can now be used to set a configuration blob
through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
The radio_work type was stored within the dynamically allocated
wpa_radio_work buffer and that buffer ended up getting freed before the
final use of the type string within radio_work_done(). This resulted in
freed memory being used for a debug print. Avoid this by freeing the
wpa_external_work instance after having completed radio_work_done() for
the related work.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.
Signed-hostap: Peter Qiu <zqiu@chromium.org>
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.
Signed-off-by: Beni Lev <beni.lev@intel.com>
The pos pointer can be compared to the start of the buffer pointer to
determine whether the entry is the first one in the list. This gets rid
of some static analyzer warnings about unused variable writes.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can request OSU icon data with "hs20_icon_request <BSSID>
<icon filename>". This transmits an Icon Request ANQP element and
processes the response in Icon Binary File ANQP elements.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter was actually used in some testing cases in a way that did
not really work well with the FLUSH command ending up disabling PMF.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The more generic NFC_REPORT_HANDOVER is now used to report completed NFC
connection handover operations in either role and NFC_RX_HANDOVER_REQ
did not have any implementation within wpa_supplicant.
Signed-off-by: Jouni Malinen <j@w1.fi>
Memory allocated by calling function ieee802_11_vendor_ie_concat()
was not freed on an error path int ctrl_iface BSS command.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
P2P persistent connection may fail due to 802.11d channel change event
invalidating support of the operating frequency sent in the invitation
request, before receiving the invitation response. If the operating
frequency is invalid at the time the invitation response is processed
and there is no forced frequency provided by user, allow frequency
re-selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If P2P was disabled (e.g., due to driver not supporting it or through
p2p_disabled=1 configuration), setting Wi-Fi Display parameters could
result in segmentation fault when the WFD IE is updated without the P2P
module being initialized. Fix this by skipping the update if P2P module
is not in use. In addition, show Wi-Fi Display as disabled in "GET
wifi_display" and refuse to enable it with "SET wifi_display 1" if P2P
is not enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to force an operating channel for P2P group formation
triggered by NFC operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These optional attributes, if present, can be used to speed up the
initial connection by using a single channel scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If CONFIG_WPS_TESTING=y is enabled in build configuration, the new
wps_corrupt_pkhash parameter (similar to wps_testing_dummy_cred) can be
used to request public key hash to be corrupted in all generated OOB
Device Password attributes. This can be used for testing purposes to
validate public key hash validation steps.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the NFC connection handover message received from a peer indicates
that the peer is operating as a GO on a specific channel, use that
information to avoid having to go through full scan. In addition, skip
the separate join-a-group scan since we already know the operating
channel, GO P2P Device Address, and SSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_GET_HANDOVER_{REQ,SEL} NDEF P2P-CR" can now be used to build P2P
alternative carrier record for NFC connection handover request/select
messages.
Static connection handover case can be enabled by configuring the DH
parameters (either with wps_nfc_* configuration parameters or with
WPS_NFC_TOKEN command at run time. The NFC Tag contents can be generated
with "NFC_GET_HANDOVER_SEL NDEF P2P-CR-TAG" after having configured
Listen channel (p2p_listen_reg_class/p2p_listen_channel).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New functionality is needed for this with the update NFC connection
handover design that depends on the AP side using the public key hash
from the handover request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is more useful to be able to build a single NFC carrier record
instead of the full connection handover request message to allow
external components to decide whether to negotiate which alternative
carrier is used. This updates the carrier record contents to the new
design to include Enrollee public key hash and provides this as a
carrier record instead of full message. An external program is expected
to be used to build the full NFC connection handover message with
potentially other alternative carrier records included.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the SSID of the WPS AP is known, it should be possible to limit AP
selection based on this when searching for an active WPS AP. This commit
adds a mechanism to specify SSID for this type of uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient for test scripts to change parameters for
a specific test case without having to separately clear them between
each test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify wpa_s->radio pointer before accessing it. If interface addition
fails, this could get called before wpa_s->radio has been set.
The segmentation fault details:
Program received signal SIGSEGV, Segmentation fault.
0x00000000004b9591 in wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
5754 dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,
Call stack:
0 wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
1 wpa_supplicant_deinit_iface (wpa_s=0x77fff0, notify=0, terminate=0) at wpa_supplicant.c:3619
2 wpa_supplicant_add_iface (global=0x75db10, iface=0x7fffffffe270) at wpa_supplicant.c:3691
3 wpas_p2p_add_p2pdev_interface (wpa_s=0x75dd20) at p2p_supplicant.c:3700
4 main (argc=<optimized out>, argv=<optimized out>) at main.c:317
Function:
5750 void wpas_ctrl_radio_work_flush(struct wpa_supplicant *wpa_s)
5751 {
5752 struct wpa_radio_work *work, *tmp;
5753
5754 dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,
5755 struct wpa_radio_work, list) {
5756 struct wpa_external_work *ework;
5757
5758 if (os_strncmp(work->type, "ext:", 4) != 0)
Root cause:
(gdb) p wpa_s->radio
$1 = (struct wpa_radio *) 0x0
Signed-hostap: Max Stepanov <Max.Stepanov@intel.com>
It should be noted that these commands are not exclusively used for P2P
or in the global context, so use of these commands through the global
control interface for operations that are specific to a single interface
have undefined behavior and that behavior may change in the future. As
such, these are recommend only for operations that are in the global
context (e.g., for P2P management).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
All te network blocks and credentials were already cleared, but
configurations blobs should also be cleared here, e.g., to get
more consistent behavior test cases using EAP-FAST PACs.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to limit which channels are scanned using the specified
list of frequency ranges in the same format that the SCAN command uses.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.
Signed-hostap: Jouni Malinen <j@w1.fi>
The newer wpa_dbg() print includes the same information in a more
convenient form, so remove the duplicate RX ctrl_iface hexdump in the
cases where there is no key material in the control interface commands
(the possible-key-material case is still using wpa_hexdump_ascii_key).
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).
In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to enable various testing parameters and
functionality in build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an array of ciphers and a loop instead of copy-pasted copies of the
same printing functionality for each cipher.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
While starting from PNO start context, the scheduled scan was not
setting the flag wpa_s->scanning. This was resulting in the subsequent
SCAN command to proceed further and send command to nl80211/cfg80211.
The expected behavior of cancelling sched_scan was not happening here.
While sched_scan is in progress and a legacy scan comes on the
cli/socket, the sched_scan is cancelled and normal scan is allowed to
continue. However, sometimes sched_scan cancelled event comes a bit
delayed and we will send out the scan command before the wpa_s->scanning
is cleared. Instead, reschedule the incoming scan req if the
wpa_s->scanning shows that it is still in progress.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This triggers re-transmission of CTRL-EVENT-STATE-CHANGE and
CTRL-EVENT-CONNECTED events on STATUS command for Android framework
specific processing.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.
This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows sp_type={home,roaming,unknown} to be used to determine
network type with SIM-based credentials even if the domain name
parameter is not configured explicitly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it less likely to forget WPS single-channel scan optimization
in effect after having completed the WPS operation or in case WPS
operating gets cancelled.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is what the original implementation did years ago, but the move to
using separate control interface backends re-ordered the implementation
to process EAPOL notification first. Use a registered timeout to allow
the ctrl_iface response to be sent out first to get somewhat faster
response time and to avoid pending operations that could result in
ctrl_iface response and unsolicited event messages from getting mixed
up.
Signed-hostap: Jouni Malinen <j@w1.fi>
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible that a P2P GO has been discovered through a non-P2P scan
that did not return P2P IE in Probe Response frames. To cover those
cases, check also Beacon frame (if received) for P2P IE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The interval for the PNO scan did not use the configured sched_scan
interval. This commit addresses the same by using the configured value
or the default of 10 seconds if configuration parameter is not used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
This provides global status information that is applicable to all
interfaces (e.g., P2P state). In addition, ifname/address pairs are
listed to get information of all the interfaces that are currently
managed through this wpa_supplicant instance.
Signed-hostap: Jouni Malinen <j@w1.fi>
This iterates through all interfaces and saves configuration file
updates for each interface that allows it (update_config=1).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows global parameters to be set through the global control
interface without having to use IFNAME prefix. For now, this covers
only the wifi_display parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
