After station interface is connected on a specific channel, create
autonomous GO with forced different channel.
Requires MCC.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Verify that when P2P group is formed and a station interface is
connected on a channel that is disallowed for P2P, the group is formed
on a different channel than the BSS (both as GO and client).
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when setting up an autonomous GO and station interface is
connected on a channel that is disallowed for P2P uses, the GO is
instantiated on a different channel than the station mode connection.
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when station interface is connected and GO negotiation is
initiated, the P2P group is formed on the same channel as the station
connection.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This test verifies that if a GO is instantiated after a connection of a
station interface, the chosen operating channel is that of the station
interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add an option to run-all.sh and start.sh to get as an argument the
number of concurrent channels that mac80211_hwsim will be loaded with.
To start mac80211_hwsim with more than one channel, the following
parameter should be added to command line: channels=<num_channels>
The default is one channel (no concurrent channels).
The driver should be loaded with multi channel support in order to run
some tests.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
This test case shows an example case where an uncancelled offchannel TX
frame command seems to end up getting following CMD_FRAME TX operations
transmitting on incorrect channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
This introduces a minimal RADIUS authentication server using pyrad to
allow simple EAP handler functions to be used for writing protocol tests
for EAP peer methods. This initial commit includes test cases for
EAP-SAKE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for printf_encode() bounds checking issues
that can now be caught under valgrind.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only hostapd-AP and wpa_supplicant processed were run under
valgrind when valgrind testing was enabled. Extend this to include
hostapd as authentication server.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was still present in hostapd example configuration even though the
test driver wrapper is not used anywhere in the hwsim testing and there
are no plans of using it either.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the existing test cases where PTK rekey was
triggered by the station, but here a timer on the AP is used as the
trigger.
Signed-off-by: Jouni Malinen <j@w1.fi>
This brings in a minimal pyrad-based RADIUS server to allow various
protocol tests to be run. For now, the server is not adding
Message-Authenticator, so that error case is checked. Additional tests
can be added in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
This used to result in a segmentation fault due to use of freed memory
(mismatch in pointer lifetime between hostapd.c and driver_nl80211.c).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for an issue where scanning sequence could be
terminated if interworking_find_network_match() finds a matching
network, but wpa_s->auto_select is not set. This could stop connection
attempts when auto_interworking=1 is used and the scan results have a
partially matching network and no cred match.
Signed-off-by: Jouni Malinen <j@w1.fi>
radius_{auth,acct}_unreachable tested some parts of RADIUS client code
error handling. However, they did not test everything since the send()
calls for unreachable port on localhost did not return an error (that
error was reported on receive side). Extend this with similar test cases
using unreachable IP address to get send() error returns covered as
well.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_cipher_tkip_countermeasures_{ap,sta} printed out the MAC addresses in
stdout which resulted in the debug log not starting the PASS/FAIL
information at the beginning of the line. Hide these unnecessary prints
to avoid that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
