Commit graph

196 commits

Author SHA1 Message Date
Jouni Malinen
f8608fab85 SME: Fix SA Query local failure handling
If no new sme_sa_query_timer() callback is scheculed,
sme_stop_sa_query() needs to be called to allow new SA Query operations
to be started after the failure.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-07-18 00:57:34 +03:00
Kanchanapally, Vidyullatha
cc9a2575ca nl80211: Use extended capabilities per interface type
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 21:35:54 +03:00
Beni Lev
00ed0aa2dd SME: Add support for global RRM flag
Add RRM to SME authentication/association if the global RRM flag is set.

Signed-off-by: Beni Lev <beni.lev@intel.com>
2016-04-17 12:43:57 +03:00
David Spinadel
4a742011ab wpa_supplicant: Handle LCI request
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with

SET lci <hexdump of the element>

and cleared with

SET lci ""

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-17 12:29:12 +03:00
Matti Gottlieb
ece4ac5f4e HS 2.0: Add support for configuring frame filters
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:

1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
   DGAF disabled bit is zero

Clear the filter configuration when the station interface is
disassociated.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 15:21:18 +03:00
Lior David
ba307f8528 P2P: Add a separate pointer to the P2P Device instance
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.

Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Avraham Stern
c484b19882 Move Hotspot 2.0 element in (Re)Association Request frames
According to IEEE Std 802.11-2012, Table 8-22, vendor specific elements
must follow all other elements, so Hotspot 2.0 element which is actually
a vendor specific element must come after all other elements.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
a0c38e5dd7 Re-order elements in (Re)Association Request frames
According to IEEE Std 802.11-2012, Table 8-22, RM Enabled Capabilities
element must come before the Extended Capabilities element.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
5e57ba2505 MBO: Add Supported Operating Classes element to Association Request
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
92c6e2e3a9 MBO: Implement MBO non-preferred channel report in Association Request
Add MBO IE with non-preferred channels to (Re)Association Request
frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
ea69d9737c wpa_supplicant: Share a single get_mode() implementation
There is no need to duplicate this helper function in multiple files.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-21 17:14:51 +02:00
Masashi Honma
70c93963ed SAE: Fix PMKID calculation for PMKSA cache
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-02-18 21:07:47 +02:00
Kanchanapally, Vidyullatha
4ead7cfd5d Abort an ongoing scan before connect
Connect radio work is sometimes delayed for a considerable duration if
there is an ongoing scan radio work. To avoid these delays abort the
ongoing scan on that interface before queuing a connect request. Upon a
scan done indication from the driver, connect radio work will be
scheduled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Jouni Malinen
ec4387f9c9 Indicate CTRL-EVENT-AUTH-REJECT event on authentication rejection
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 19:11:02 +03:00
Hu Wang
6108536d7d Drop connection attempt if network is disabled before radio work starts
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-10 22:16:19 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Jouni Malinen
6a58444d27 SAE: Verify that own/peer commit-scalar and COMMIT-ELEMENT are different
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-23 23:10:36 +03:00
Jouni Malinen
04e6c4cc50 Fix SAE group selection in an error case
The sae_groups parameter is zero terminated array, not -1 terminated, so
must check the value against <= 0 to break out from the loop.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-20 23:29:57 +03:00
Jouni Malinen
ee140ef98f FT: Stop association attempt if Auth response processing fails (SME)
Call the FT processing function directly instead of going through
wpa_supplicant_event() to process FT Authentication frame in SME case.
This allows parsing error to be used to trigger immediate failure for
the connection instead of trying to proceed to reassociation step that
cannot succeed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-20 17:36:58 +03:00
Jouni Malinen
59b416c733 Add optional reassoc-to-same-BSS optimization
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 16:35:39 +02:00
Jouni Malinen
ba4226130e Simplify eapol_sm_notify_pmkid_attempt()
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-28 13:09:31 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Jouni Malinen
d29fa3a767 Extend VENDOR_ELEM parameters to cover non-P2P Association Request
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-14 01:12:56 +02:00
Jouni Malinen
4e70bbf1c6 SAE: Clear keys from memory on disassociation
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 20:00:02 +02:00
Jouni Malinen
d97a3c4885 SME: Optimize OBSS scanning
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 22:07:03 +02:00
Jouni Malinen
267ac3bcd6 Add more debug prints for WPA/RSN selection issues for connection
ap_ft_sae test case managed to hit a somewhat unclear error case which
resulted in "WPA: Failed to select WPA/RSN" print and not enough
information to figure out what exactly had went wrong.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 13:49:52 +02:00
Jouni Malinen
81648d0041 SAE: Report connection failure if SME cannot build auth frame
Instead of just stopping connection process and network discovery,
report SAE failures to build Authentication frames (e.g., due to missing
password) as a connection failure to get the normal retry mechanism into
use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 16:48:38 +02:00
Masashi Honma
a959a3b69d SAE: Fix Anti-Clogging Token request frame format
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-25 16:08:53 +02:00
Jouni Malinen
849367afe9 SME: Fix a sign-compare warning
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 01:07:16 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Jouni Malinen
a7f5271d52 Update pending connect radio work BSS pointer on scan update
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).

Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-28 00:43:58 +02:00
Jouni Malinen
bc26ac50dd SAE: Add support for PMKSA caching on the station side
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 13:02:02 +03:00
Janusz Dziedzic
4ec68377ef wpa_supplicant: Use hostapd_freq_params in assoc_params
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-10-04 18:43:42 +03:00
Jouni Malinen
cb5ef952c8 SME: Verify that os_get_random() succeeds for SA Query
Be more consistent on checking os_get_random() return value (CID 72706).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 18:27:42 +03:00
Jouni Malinen
745ef18478 HS 2.0: Verify assoc_req_ie buffer size for indication elements
While the buffer is expected to be large enough for all the IEs, it is
better to check for this explicitly when adding the HS 2.0 Indication
element. (CID 68601)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Johannes Berg
57a8f8af38 nl80211: Use low-priority scan for OBSS scan
Some drivers may support low-priority scans, if they do then
use that for OBSS scanning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-22 00:47:06 +03:00
Jouni Malinen
3302b7c29f Rate limit SA Query procedure initiation on unprotected disconnect
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-19 20:56:32 +03:00
Jouni Malinen
0bbaa9b93f Validate driver extended capabilities length against buffer length
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 16:35:30 +03:00
Ilan Peer
d0df643735 wpa_supplicant: Call frequency conflict handling during auth
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.

Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.

In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-04-24 12:15:32 +03:00
Ilan Peer
f1c4dbf5cd wpa_supplicant: Remove pending sme-connect radio work
If a new connection is attempted while there is a pending sme-connection
radio work, cancel the pending radio work and continue with the new
connection attempt. This is preferable over rejecting the new work and
continuing with the pending one, as it is possible that the previous
work is no longer valid.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-27 16:45:25 +02:00
Jouni Malinen
163f801ef2 nl80211: Indicate HS 2.0 OSEN AKM in connect/associate command
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 18:33:21 +02:00
Jouni Malinen
31ded52e70 SME: Add more debug prints for OBSS scans and 20/40 MHz co-ex report
This makes it easier to debug wpa_supplicant behavior when reporting
20/40 MHz co-ex information based on OBSS scans.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:56:50 +02:00
Jouni Malinen
7f8eb34dee SME: Fix OBSS scan result processing for 20/40 MHz co-ex report
The 40 MHz intolerant bit needs to be checked before skipping the BSS
based on the channel already being in the lost (which could have
happened due to another BSS that does not indicate 40 MHz intolerant).
This fixed the 20/40 MHz co-ex report to indicate 20 MHz request
properly if there are both 40 MHz tolerant and intolerant BSSes on the
same channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:54:50 +02:00
Jouni Malinen
df0f01d91f HS 2.0R2: Add OSEN client implementation
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Jouni Malinen
f0e30c8410 Do not start another connect work while one is pending
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-24 15:22:35 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Jouni Malinen
d950477913 Fix authentication algorithm negotiation in SME code
Commit 6ac4b15ef8 (wpa_radio work for
connection) caused a regression for cases where multiple auth_alg values
are set in a network block and wpa_supplicant-based SME is supposed to
iterate through them. The connection radio work was not terminated when
receiving authentication failure and this resulted in the following
authentication attempt failing.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-02-03 19:34:33 +02:00
Jouni Malinen
6ac4b15ef8 Use wpa_radio work for connection
This protects against conflicting offchannel operations during
connection (authentication, association, EAP exchanges, 4-way
handshake).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
4848a38d85 Get rid of duplicated cipher suite and AKM definitions
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 09:16:27 +02:00
Johannes Berg
46b8d4c004 wpa_supplicant: Use monotonic time for SA query timeout
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:17:25 +02:00
Jouni Malinen
18ca733248 SAE: Fix group selection
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-02 18:07:49 +02:00
Jouni Malinen
d7df0fa727 Clean up wpa_supplicant_event() with deauth/disassoc helper functions
wpa_supplicant_event() has grown overly large, so it is useful to split
it into smaller pieces.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 16:40:40 +03:00
Jouni Malinen
55a2df4389 HS 2.0: Include HS 2.0 Indication element only for HS 2.0 association
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-05 16:29:21 +03:00
Jouni Malinen
e864c0aefe Use a common frequency to channel conversion function
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-27 22:11:51 +03:00
Chet Lanctot
3ee9ade6cf Allow SME SA Query to be used by all drivers
The unprotected disconnection events were previously processed only for
drivers that used the wpa_supplicant SME implementation (separate
authentication and association commands). However, this can be useful
for drivers that use the connect API, so remove the limitation and allow
the same IEEE 802.11w SA Query mechanism to be used even without full
use of the wpa_supplicant SME.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-11 13:49:40 +02:00
Johannes Berg
e9ee8dc394 wpa_supplicant: Support VHT capability overrides
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-10 18:04:39 +02:00
Jouni Malinen
62769a88db Move cipher to enum wpa_cipher conversion into wpa_common.c
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 18:02:20 +02:00
Jouni Malinen
b4fd3613d3 SAE: Free temporary buffers when moving to Accepted state
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:54 +02:00
Jouni Malinen
4ef34a9960 SAE: Remove duplicated SAE field debug dumps
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:54 +02:00
Jouni Malinen
625f202a74 SAE: Allow enabled groups to be configured
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
a46d72d7d7 SAE: Maintain EC group context in struct sae_data
This can be used to share same EC group context through the SAE
exchange.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
d136c376f2 SAE: Add support for Anti-Clogging mechanism
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
dd43026a19 SAE: Rename state variables to match IEEE 802.11 standard
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
47b55a3ef5 SAE: Use PMK in 4-way handshake
Use the PMK that is derived as part of the SAE authentication in the
4-way handshake instead of the PSK.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
f2e9818f73 SAE: Add processing of the confirm message
This adds validation of the received confirm messages for SAE.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
fb8fcc2950 SAE: Add generation of the confirm message fields
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
146f6c9a00 SAE: Add processing of the commit message
This adds validation of the received commit messages and key derivation
for SAE.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
8e31e9550a SAE: Add generation of the commit message fields
This adds derivation of PWE and the needed commit values so that the
full SAE commit message can be built.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
98efcc4176 SAE: Use a shared data structure for AP and station
This makes it easier to share common functions for both roles.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00
Jouni Malinen
03e47c9c3a Share a single function for building extended capabilities element
This makes it easier to update extended capabilities for all uses
within wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 19:17:15 +02:00
Jouni Malinen
e6955ba9f9 WNM: Add WNM-Sleep Mode into Extended Capabilities element
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:45:59 +02:00
Jouni Malinen
215ae884d6 Mark sme_send_authentication() static
This function is not used outside sme.c.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 15:47:43 +02:00
Jouni Malinen
62d4980331 Allow PMF to be enabled by default
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-24 22:21:29 +02:00
Amitkumar Karwar
368b1957a6 Allow OBSS scan and 20/40 coex reports to non-SME drivers
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
2012-11-24 18:08:48 +02:00
Jouni Malinen
6e2020210a Allow OKC to be enabled by default
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-12 20:07:53 +02:00
Jouni Malinen
21af6d15a8 SAE: Add Finite Cyclic Group negotiation and Send-Confirm
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-10-06 19:30:54 +03:00
Jouni Malinen
c10347f246 Add initial parts for SAE
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-30 19:51:07 +03:00
Jouni Malinen
a3f7e5186b Allow non-WPA IEEE 802.1X to be select even if WPA is also enabled
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-15 19:34:04 +03:00
Jouni Malinen
067ffa2696 Convert os_realloc() for an array to use os_realloc_array()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 21:21:23 +03:00
Jouni Malinen
f9884c096a Convert os_zalloc() for an array to use os_calloc()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 20:44:21 +03:00
Arik Nemtsov
b6871ebb17 SME: Correctly check mode HT caps for enabling OBSS scan
Don't assume the 11g mode is always first in the list of mode (sometimes
it isn't). Traverse the array of modes and check the HT40 capability is
turned on for 11g.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
2012-08-11 17:08:54 +03:00
Jouni Malinen
c1c023429b Set state to DISCONNECTED on auth/assoc failures
Some of the authentication/association failure paths left wpa_state to
its previous value. This can result in unexpected behavior when
wpa_supplicant tries to find an AP to connect to since the uncleared
state can result the in the selected BSS being ignored if it is same as
the previously used BSS. This could happen, e.g., when wpa_supplicant
SME was used and the AP rejected authentication. Fix this by explicitly
setting state to DISCONNECTED on auth/assoc failures that did not yet do
this.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-06-25 14:23:25 +03:00
Jouni Malinen
cb4183249f HS 2.0: Add HS 2.0 Indication element into (Re)Association Request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 23:30:04 +03:00
Jouni Malinen
6434ad09d6 Scan only 2.4 GHz band for OBSS scans
Since we are reporting 20/40 BSS coex information only for 2.4 GHz band,
there is no need to run the full scan on dualband cards.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-03 15:55:42 +03:00
Rajkumar Manoharan
c3701c66a5 Add handling of OBSS scan requests and 20/40 BSS coex reports
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.

Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-03 15:55:38 +03:00
Bala Shanmugam
1f6c0ab872 Allow background scan period to be configured
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.

Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
2012-03-30 15:20:35 +03:00
Jouni Malinen
0f3d578efc Remove the GPL notification from files contributed by Jouni Malinen
Remove the GPL notification text from the files that were
initially contributed by myself.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Ben Greear
80e8a5eef1 Support HT capability overrides
This allows HT capabilities overrides on kernels that
support these features.

MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.

HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.

HT40 can be disabled.

MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.

Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2012-01-29 21:01:31 +02:00
Eyal Shapira
1193dc8fd7 SME: Fix processing of Authentication timeout and failure
current_bss and pending_bssid weren't cleaned up so BSS
kept appearing in the scan results even when it was actually gone.
Use wpa_supplicant_mark_disassoc() to cleanup the wpa_s context
instead of just dropping wpa_state back to DISCONNECTED.

Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-hostap: Eyal Shapira <eyal@wizery.com>
2012-01-29 17:44:31 +02:00
Jouni Malinen
14115a1089 SME: Fix processing of Authentication timeout
The wpa_state needs to be dropped back to DISCONNECTED to allow scan
results to trigger a new authentication attempt.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 22:27:48 +02:00
Jouni Malinen
ed57c5907e SME: Fix processing of Authentication request failure
The wpa_state needs to be dropped back to DISCONNECTED to allow scan
results to trigger a new authentication attempt. In addition, we can use
wpas_connection_failed() instead of requesting a scan after a fixed time
to make this error case more consistent with other similar error paths
in sme.c.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 21:04:24 +02:00
Jouni Malinen
0bf927a03e Use wpa_key_mgmt_*() helpers
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-24 22:47:46 +02:00
Jouni Malinen
19df9b0761 Mark local functions static
These functions are not used outside the file in which they are defined.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-18 21:53:36 +02:00
Jouni Malinen
a17539ebcd Remove unnecessary include file inclusion
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-13 22:13:04 +02:00
Jouni Malinen
b106173a82 Add no_cck parameter for send_action() driver_ops
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 21:49:46 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Jouni Malinen
92cbcf9128 Add Extended Capability element to AssocReq for Interworking
If Interworking is enabled, add Extended Capability element to
(Re)Association Request frames to indicate support for Interworking.
2011-10-16 23:55:34 +03:00
Luciano Coelho
a4cba8f1e2 Use sched_scan in driver init
This patch uses sched_scan, if available, when the driver is
initialized. It also adds a couple of cancel operations where
appropriate.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00