The WPS component keeps a copy of the network interface MAC address.
When MAC address is changed the WPS copy was not updated so WPS M1
message contained the old address. Some devices check this field
and fail connection attempts.
Update the WPS MAC address on interface MAC address changes.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the backhaul STA needs to add
a Multi-AP IE to the WFA vendor extension element in the WSC M1 message
that indicates it supports the Multi-AP backhaul STA role. The Registrar
(if it support Multi-AP onboarding) will respond to that with a WSC M8
message that also contains the Multi-AP IE, and that contains the
credentials for the backhaul SSID (which may be different from the SSID
on which WPS is performed).
Introduce a new parameter to wpas_wps_start_pbc() and allow it to be
set via control interface's new multi_ap=1 parameter of WPS_PBC call.
multi_ap_backhaul_sta is set to 1 in the automatically created SSID.
Thus, if the AP does not support Multi-AP, association will fail and
WPS will be terminated.
Only wps_pbc is supported.
This commit adds the multi_ap argument only to the control socket
interface, not to the D-Bus interface.
Since WPS associates with the fronthaul BSS instead of the backhaul BSS,
we should not drop association if the AP announces fronthaul-only BSS.
Still, we should only do that in the specific case of WPS. Therefore,
add a check to multi_ap_process_assoc_resp() to allow association with a
fronthaul-only BSS if and only if key_mgmt contains WPS.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The newer NFC_REPORT_HANDOVER command is more general version that
handles the cases where NFC_RX_HANDOVER_SEL could potentially have been
used. In addition, with the new WPS NFC design, it is important to
receive the handover request message that was used in the handover in
addition to the select message, so the NFC_RX_HANDOVER_SEL command on
its own would not be sufficient for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The more generic NFC_REPORT_HANDOVER is now used to report completed NFC
connection handover operations in either role and NFC_RX_HANDOVER_REQ
did not have any implementation within wpa_supplicant.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to force an operating channel for P2P group formation
triggered by NFC operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These optional attributes, if present, can be used to speed up the
initial connection by using a single channel scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the NFC connection handover message received from a peer indicates
that the peer is operating as a GO on a specific channel, use that
information to avoid having to go through full scan. In addition, skip
the separate join-a-group scan since we already know the operating
channel, GO P2P Device Address, and SSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is more useful to be able to build a single NFC carrier record
instead of the full connection handover request message to allow
external components to decide whether to negotiate which alternative
carrier is used. This updates the carrier record contents to the new
design to include Enrollee public key hash and provides this as a
carrier record instead of full message. An external program is expected
to be used to build the full NFC connection handover message with
potentially other alternative carrier records included.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the SSID of the WPS AP is known, it should be possible to limit AP
selection based on this when searching for an active WPS AP. This commit
adds a mechanism to specify SSID for this type of uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_supplicant can now generate the WPS carrier record for connection
handover response when acting as an ER. The AP whose configuration is
provided in this way is identified with an UUID as an argument to
wps-nfc.py.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of reporting only one connection handover message, report
completion of NFC connection handover with carrier record from both the
request and select messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 620c783753 modified
wpas_wps_ssid_wildcard_ok() prototype, but forgot to update the
non-WPS-build wrapper. Fix that to match with the new bss parameter
type and remove the now unused declaration of wpa_scan_res.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 620c783753 modified
wpas_wps_ssid_bss_match() prototype but forgot to update the non-WPS
wrapper inline function. Fix that to match with the new bss parameter
type.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.
Signed-hostap: Jouni Malinen <j@w1.fi>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
Mikael Kanstrup
Davina Lu
Sunil Dutt
Saurav Babu
Jouni Malinen
Jouni Malinen
Jouni Malinen
Ardong Chen