diff --git a/src/drivers/nl80211_copy.h b/src/drivers/nl80211_copy.h index 406010d4d..4b28dc07b 100644 --- a/src/drivers/nl80211_copy.h +++ b/src/drivers/nl80211_copy.h @@ -503,6 +503,9 @@ * TX status event pertaining to the TX request. * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the * management frames at CCK rate or not in 2GHz band. + * %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA + * counters which will be updated to the current value. This attribute + * is used during CSA period. * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this * command may be used with the corresponding cookie to cancel the wait * time if it is known that it is no longer necessary. @@ -719,6 +722,22 @@ * QoS mapping is relevant for IP packets, it is only valid during an * association. This is cleared on disassociation and AP restart. * + * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given + * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO + * and %NL80211_ATTR_ADMITTED_TIME parameters. + * Note that the action frame handshake with the AP shall be handled by + * userspace via the normal management RX/TX framework, this only sets + * up the TX TS in the driver/device. + * If the admitted time attribute is not added then the request just checks + * if a subsequent setup could be successful, the intent is to use this to + * avoid setting up a session with the AP when local restrictions would + * make that impossible. However, the subsequent "real" setup may still + * fail even if the check was successful. + * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID + * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this + * before removing a station entry entirely, or before disassociating + * or similar, cleanup will happen in the driver/device in this case. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -890,6 +909,9 @@ enum nl80211_commands { NL80211_CMD_SET_QOS_MAP, + NL80211_CMD_ADD_TX_TS, + NL80211_CMD_DEL_TX_TS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1525,10 +1547,10 @@ enum nl80211_commands { * operation). * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information * for the time while performing a channel switch. - * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter - * field in the beacons tail (%NL80211_ATTR_BEACON_TAIL). - * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter - * field in the probe response (%NL80211_ATTR_PROBE_RESP). + * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel + * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL). + * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel + * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP). * * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32. * As specified in the &enum nl80211_rxmgmt_flags. @@ -1576,6 +1598,11 @@ enum nl80211_commands { * advertise values that cannot always be met. In such cases, an attempt * to add a new station entry with @NL80211_CMD_NEW_STATION may fail. * + * @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which + * should be updated when the frame is transmitted. + * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum + * supported number of csa counters. + * * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32. * As specified in the &enum nl80211_tdls_peer_capability. * @@ -1583,6 +1610,34 @@ enum nl80211_commands { * creation then the new interface will be owned by the netlink socket * that created it and will be destroyed when the socket is closed * + * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is + * the TDLS link initiator. + * + * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection + * shall support Radio Resource Measurements (11k). This attribute can be + * used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests. + * User space applications are expected to use this flag only if the + * underlying device supports these minimal RRM features: + * %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES, + * %NL80211_FEATURE_QUIET, + * If this flag is used, driver must add the Power Capabilities IE to the + * association request. In addition, it must also set the RRM capability + * flag in the association request's Capability Info field. + * + * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout + * estimation algorithm (dynack). In order to activate dynack + * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower + * drivers to indicate dynack capability. Dynack is automatically disabled + * setting valid value for coverage class. + * + * @NL80211_ATTR_TSID: a TSID value (u8 attribute) + * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute) + * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds + * (per second) (u16 attribute) + * + * @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see + * &enum nl80211_smps_mode. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1920,6 +1975,21 @@ enum nl80211_attrs { NL80211_ATTR_IFACE_SOCKET_OWNER, + NL80211_ATTR_CSA_C_OFFSETS_TX, + NL80211_ATTR_MAX_CSA_COUNTERS, + + NL80211_ATTR_TDLS_INITIATOR, + + NL80211_ATTR_USE_RRM, + + NL80211_ATTR_WIPHY_DYN_ACK, + + NL80211_ATTR_TSID, + NL80211_ATTR_USER_PRIO, + NL80211_ATTR_ADMITTED_TIME, + + NL80211_ATTR_SMPS_MODE, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -2188,6 +2258,8 @@ enum nl80211_sta_bss_param { * Contains a nested array of signal strength attributes (u8, dBm) * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average * Same format as NL80211_STA_INFO_CHAIN_SIGNAL. + * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the + * 802.11 header (u32, kbps) * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -2219,6 +2291,7 @@ enum nl80211_sta_info { NL80211_STA_INFO_TX_BYTES64, NL80211_STA_INFO_CHAIN_SIGNAL, NL80211_STA_INFO_CHAIN_SIGNAL_AVG, + NL80211_STA_INFO_EXPECTED_THROUGHPUT, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -3036,14 +3109,20 @@ enum nl80211_bss_scan_width { * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets) * @NL80211_BSS_FREQUENCY: frequency in MHz (u32) * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64) + * (if @NL80211_BSS_PRESP_DATA is present then this is known to be + * from a probe response, otherwise it may be from the same beacon + * that the NL80211_BSS_BEACON_TSF will be from) * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16) * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16) * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the * raw information elements from the probe response/beacon (bin); - * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are - * from a Probe Response frame; otherwise they are from a Beacon frame. + * if the %NL80211_BSS_BEACON_IES attribute is present and the data is + * different then the IEs here are from a Probe Response frame; otherwise + * they are from a Beacon frame. * However, if the driver does not indicate the source of the IEs, these * IEs may be from either frame subtype. + * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the + * data here is known to be from a probe response, without any heuristics. * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon * in mBm (100 * dBm) (s32) * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon @@ -3055,6 +3134,10 @@ enum nl80211_bss_scan_width { * yet been received * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel * (u32, enum nl80211_bss_scan_width) + * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64) + * (not present if no beacon frame has been received yet) + * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and + * @NL80211_BSS_TSF is known to be from a probe response (flag attribute) * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ @@ -3072,6 +3155,8 @@ enum nl80211_bss { NL80211_BSS_SEEN_MS_AGO, NL80211_BSS_BEACON_IES, NL80211_BSS_CHAN_WIDTH, + NL80211_BSS_BEACON_TSF, + NL80211_BSS_PRESP_DATA, /* keep last */ __NL80211_BSS_AFTER_LAST, @@ -3688,6 +3773,8 @@ enum nl80211_iface_limit_attrs { * different channels may be used within this group. * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap * of supported channel widths for radar detection. + * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap + * of supported regulatory regions for radar detection. * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * @@ -3721,6 +3808,7 @@ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_STA_AP_BI_MATCH, NL80211_IFACE_COMB_NUM_CHANNELS, NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, + NL80211_IFACE_COMB_RADAR_DETECT_REGIONS, /* keep last */ NUM_NL80211_IFACE_COMB, @@ -3894,6 +3982,8 @@ enum nl80211_ap_sme_features { * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested * to work properly to suppport receiving regulatory hints from * cellular base stations. + * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: (no longer available, only + * here to reserve the value for API/ABI compatibility) * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station * mode @@ -3932,13 +4022,33 @@ enum nl80211_ap_sme_features { * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the * lifetime of a BSS. + * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter + * Set IE to probe requests. + * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE + * to probe requests. + * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period + * requests sent to it by an AP. + * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the + * current tx power value into the TPC Report IE in the spectrum + * management TPC Report action frame, and in the Radio Measurement Link + * Measurement Report action frame. + * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout + * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used + * to enable dynack. + * @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial + * multiplexing powersave, ie. can turn off all but one chain + * even on HT connections that should be using more chains. + * @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial + * multiplexing powersave, ie. can turn off all but one chain + * and then wake the rest up as required after, for example, + * rts/cts handshake. */ enum nl80211_feature_flags { NL80211_FEATURE_SK_TX_STATUS = 1 << 0, NL80211_FEATURE_HT_IBSS = 1 << 1, NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2, NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3, - /* bit 4 is reserved - don't use */ + NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4, NL80211_FEATURE_SAE = 1 << 5, NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6, NL80211_FEATURE_SCAN_FLUSH = 1 << 7, @@ -3953,6 +4063,13 @@ enum nl80211_feature_flags { NL80211_FEATURE_USERSPACE_MPM = 1 << 16, NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17, NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18, + NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19, + NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20, + NL80211_FEATURE_QUIET = 1 << 21, + NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22, + NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23, + NL80211_FEATURE_STATIC_SMPS = 1 << 24, + NL80211_FEATURE_DYNAMIC_SMPS = 1 << 25, }; /** @@ -4026,6 +4143,25 @@ enum nl80211_acl_policy { NL80211_ACL_POLICY_DENY_UNLESS_LISTED, }; +/** + * enum nl80211_smps_mode - SMPS mode + * + * Requested SMPS mode (for AP mode) + * + * @NL80211_SMPS_OFF: SMPS off (use all antennas). + * @NL80211_SMPS_STATIC: static SMPS (use a single antenna) + * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and + * turn on other antennas after CTS/RTS). + */ +enum nl80211_smps_mode { + NL80211_SMPS_OFF, + NL80211_SMPS_STATIC, + NL80211_SMPS_DYNAMIC, + + __NL80211_SMPS_AFTER_LAST, + NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1 +}; + /** * enum nl80211_radar_event - type of radar event for DFS operation *